Mila po postopku vlivanja so enostaven način izdelave prikupnih, dišečih in doma narejenih mil. Izdelava je zelo enostavna, načinov in idej za improvizacijo pa je nešteto. Moje prvo milo je bilo narejeno prav s tem postopkom. Šele kasneje sem se opogumila in naredila milo po hladnem postopku (ta način vam bom opisala drugič). Za postopek vlivanja potrebujete:
- glicerinsko milo za vlivanje (prozorno, belo,...)
- barvo za mila
- silikonski kalup
- eterična olja
- suhe cvetove
-alkohol z razpršilcem
-posodo za mešanje in kuhalnico
PRIPRAVA:
1. Glicerinsko milo narežemo na majhne dele in jih damo v posodo. Na zmernem ognju ali na vodni kopeli stopimo milo.
2. Ko se lepo utekočini dodamo barvo za mila. Jaz sem jo kupila v Art trgovini in je res dobro pigmentirana. Barva je primerna samo za mila izdelana po tem postopku. Če želite uporabiti isto barvo za mila izdelana po hladnem postopku vas moram razočarati, da ne bo imelo nobenega efekta. Ko se malo ohladi dodamo še eterična olja.
3. V kalup si predhodno natrosimo suhe cvetove, če jih želimo imeti na površini ali pa med celotno maso, da se zmešajo in jih imamo v celotni masi. Če vam cvetovi ne odgovarjajo, jih lahko tudi izpustite.
4. Milo se zelo hitro suši, tako da v kalupe vlivajte karseda hitro. Na površini se naredijo majhni mehurčki, katere takoj pošpricamo z alkoholom ter tako izginejo. Pustimo jih na sobni temperaturi, da se strdijo, jih previdno vzamemo iz kalupa in jih zavijemo v folijo.
Namig: Izberete lahko glicerinsko milo bele in prozorne barve ter tako naredite posebne efekte. Lahko naredite prelivajoč motiv (prozorno bo manj intenzivno kot belo), pri prozornem se bodo lepo videla zelišča idr.
Milo je hitro narejeno in primerno za darilo, ko nimate časa čakati nekaj tednov, da se strdi (tako kot pri milu narejenem po hladnem postopku). Sestavine sem v večini kupila preko spletne strani Calendula in nekaj v trgovini Art.
Čiščenje posod je enostavno vendar vseeno priporočam, da za pripravo uporabite posebno posodo, ki jo imate potem samo za izdelavo mil.
English:
Melt&pour soaps are an easy way of making cute, fragrant and home-made soaps. Ideas for improvisation are endless. My first soap was done exactly with this procedure. After this I made soap with cold process (I will describe the next time how you do this ). For melt&pour soap you need:
- glycerine soap for casting (clear, white, ...)
- color for soap
- silicone mold
- essential Oils
- dried flowers
- alcohol with sprayer
- container and a mixing spoon
PREPARATION:
1. Cut glycerine soap into small pieces and put them in a bowl. Melt the soap on low heat or in a water bath.
2. When its all liquefied add color to the soap. I bought it in Art store and its really well pigmented. The color is suitable only for soap produced by this procedure. If you want to use the same color for soap made with cold process I have to disappoint you, it will have no effect. When it cools a little bit add essential oils.
3. Before casting give in the mold dried flowers, if you want them on the surface or give them in the entire mass to mix them in the whole mass. If you do not like flowers you can skip them.
4. Soap dries very quickly. Pour into molds as soon as possible. On the surface could be made small bubbles which spray immediately with alcohol to disappear. Leave it at room temperature to harden it and then carefully remove the soap from the mold and wrap him in foil.
Tip: You can use white or transparent glycerine soap to make special effects. You can make a flowing motive (clear will be less intense than white), with clear soap its nice to see the herbs and others.
Soap is quickly done and suitable for gift when you do not have time to wait a few weeks to harden them (like soap made with cold process). I bought the ingredients from the webside Calendula (the most from them) and some in the Art shop.
Cleaning containers is easy but I recommend to use special container just for making the soap.
Ni komentarjev:
Objavite komentar